Union by Co-Lamination of Aluminum and Magnetic alloy obtained by Rapid Solidification

Francisco Garcia Almassio; Marcelo Ruben Pagnola; Fabiana Saporitti; Fernando Audebert

doi:10.32397/tesea.vol3.n2.486

Authors

Francisco Garcia Almassio Facultad de Ingeniería de la Universidad de Buenos Aires, CABA, Argentina https://orcid.org/0000-0002-6355-4129
Marcelo Ruben Pagnola INTECIN (UBA-CONICET)
Fabiana Saporitti Facultad de Ingeniería de la Universidad de Buenos Aires, CABA, Argentina
Fernando Audebert Facultad de Ingeniería de la Universidad de Buenos Aires, CABA, Argentina

DOI:

https://doi.org/10.32397/tesea.vol3.n2.486

Keywords:

COLAMINATION, RAPID SOLIDIFICATION, MELT SPINNING, HYSTERESIS, EDDY CURRENT

Abstract

The aim of this work is to analyze the possibility of producing a joint by lamination of an Al-1050 plate and Fe₇₈Si₉B₁₃(%at.) soft magnetic ribbons material obtained by a rapid solidification process by using the Melt Spinning (MS) technique. The lamination conditions are studied on the characteristics of the joint, the microstructure, and the magnetic properties. Mainly the surface preparation, temperature, and reduction of thickness. The material is characterized by X-Ray Diffraction, Optical, and Scanning Electron Microscopy, showing a completely amorphous structure before and after the collamination, the typical defects caused by this rapid solidification technique in ribbons (bubbles, dust particles, roughness imperfections and oxides) and the joint between materials. The microhardness Vickers has been determined in both, the ribbons as quenched and collaminated samples, to observe quantitatively the hardening suffered during colamination and find a possible cause. The Differential Scanning Calorimetry and Compositional Analysis by EDS techniques were also used to determine the crystallization temperatures and chemical exact chemical composition of the ribbons as received. The magnetic hysteresis curve of the amorphous ribbons showed a Hc and Ms around 3.8 A/m and 1.44 T correspondingly.

Downloads

Download data is not yet available.

References

[1] M. Pagnola and H. Sirkin. Materiales magnéticos modernos, May 2018. Avaliable at https://www.revistapetroquimica.com/materiales-magneticos-modernos/.
[2] D Muraca, J Silveyra, M Pagnola, and V Cremaschi. Nanocrystals magnetic contribution to finemet-type soft magnetic materials with ge addition. Journal of Magnetism and magnetic Materials, 321(21):3640–3645, 2009.
[3] Marcelo R Pagnola, Marcelo Barone, Mariano Malmoria, and Hugo Sirkin. Influence of z/w relation in chill block melt spinning (cbms) process and analysis of thickness in ribbons. Multidiscipline Modeling in Materials and Structures, 2015.
[4] KH J. Buschow. J. Appl. Phys., 53:7713, 1982.
[5] Giselher Herzer. Modern soft magnets: Amorphous and nanocrystalline materials. Acta Materialia, 61(3):718–734, 2013.
[6] Pu Wang, Min Wei, Yannan Dong, Zhengqu Zhu, Jiaqi Liu, Jing Pang, Xiaoyu Li, and Jiaquan Zhang. Crystallization evolution behavior of amorphous fe85. 7si7. 9b3. 6cr2c0. 8 powder produced by a novel atomization process. Journal of Non-Crystalline Solids, 594:121824, 2022.
[7] R. A. Serway and J. W. Jewett. Physics I, 3rd Edition. Cengage Learning Ed, 2004.
[8] Marcelo R Pagnola, Mariano Malmoria, Marcelo Barone, and Hugo Sirkin. Analysis of fe78si9b13 (% at.) ribbons of noncommercial scrap materials produced by melt spinning equipment. Multidiscipline Modeling in Materials and Structures, 2014.
[9] M Pagnola, M Malmoria, and M Barone. Biot number behaviour in the chill block melt spinning (cbms) process. Applied Thermal Engineering, 103:807–811, 2016.
[10] Marcelo Rubén Pagnola, Jairo Useche Vivero, and Andres Guillermo Marrugo. New uses of micro and nanomaterials. IntechOpen, 2018. Avaliable at https://www.intechopen.com/books/6851.
[11] A Cabral-Prieto, F García-Santibáñez, A López, R López-Castañares, and O Olea Cardoso. Vickers microhardness and hyperfine magnetic field variations of heat treated amorphous fe78si9b13 alloy ribbons. Hyperfine Interactions, 161(1):69–81, 2005.
[12] NN Zhuravlev. X-ray determination of the structure of sib. Kristallografiya, 1(6):666–68, 1956.
[13] J Zhang and F Guyot. Thermal equation of state of iron and fe0. 91si0. 09. Physics and Chemistry of Minerals, 26(3):206–211, 1999.
[14] Sterling B Hendricks and Peter R Kosting. Xxxv. the crystal structure of fe2p, fe2n, fe3n and feb. Zeitschrift für Kristallographie-Crystalline Materials, 74(1-6):511–533, 1930.
[15] Narges Amini, Július Dekan, Milan Pavúk, Safdar Habibi, and Marcel Miglierini. Influence of quenching rate on the structure, morphology, and hyperfine parameters of amorphous ribbons. Journal of Electrical Engineering, 67(5):365, 2016.
[16] Aleksandr Markovich Glezer and NA Shurygina. Amorphous-nanocrystalline alloys. CRC Press, 2017.
[17] JM Cadogan, SJ Campbell, J Jing, CP Foley, P Kater, and YW Mai. Annealing embrittlement of fe78si9b13 (metglas-2605s2). Hyperfine Interactions, 226(1):7–14, 2014.
[18] Teruo Bitoh, Akihiro Makino, and Akihisa Inoue. Origin of low coercivity of fe-(al, ga)-(p, c, b, si, ge) bulk glassy alloys. Materials transactions, 44(10):2020–2024, 2003.
[19] A Makino, T Bitoh, A Kojima, A Inoue, and T Masumoto. Low core losses of nanocrystalline fe–zr–nb–b soft magnetic alloys with high magnetic flux density. Materials Science and Engineering: A, 304:1083–1086, 2001.
[20] Richard M Bozorth. Ferromagnetism. Wiley-IEEE Press, 1993.
[21] F. Garcia Almassio. Unión por Co-Laminación de Aluminio y aleación Magnética obtenida por Solidificación Rápida. Universidad de Buenos Aires, 2019.